Rapid Trigger Actuation Test — Key Speed Tester
A rapid trigger actuation test measures how effectively your keyboard's actuation point and sensitivity settings translate into registered inputs during high-speed key presses. On Hall Effect keyboards, there are two separate settings that determine actuation behavior: the actuation point (how far down you must press before the key registers, adjustable from 0.1mm to 4.0mm) and the rapid trigger sensitivity (the minimum upward travel required before a new press can register, adjustable from 0.1mm to 2.0mm). Getting these two settings right is the most important factor in extracting the full performance benefit from a rapid trigger keyboard — the hardware has a theoretical ceiling, but incorrect settings leave most of that potential unrealized. The recommended competitive defaults — based on community testing from Wooting forums, Glorious Gaming guides, and hardware review consensus in 2026 — are an actuation point of 1.5–2.0mm (reduces accidental keypresses while keeping registration fast) and a rapid trigger sensitivity of 0.2–0.4mm (fast re-actuation without false triggers from vibration or finger resting pressure). Settings below 0.1mm sensitivity create false positive inputs for most users. This actuation test measures your presses per second and average hold time — the two outputs that best reveal whether your actuation settings are correctly optimized for competitive use. A hold time above 80ms combined with a PPS below 10 usually indicates either the actuation point is set too deep (requiring more travel per press) or rapid trigger sensitivity is set too high.
Choose Your Rapid Trigger Test Angle
Each variant targets a different keyword cluster and use case for rapid trigger technology.
Rapid Trigger Speed Test
Mash a key for 5s — measures presses/sec & hold-release timing
⌨️
Press Space as fast as you can for 5 seconds
Tests your key actuation speed and hold-release timing
Key Actuation Speed Reference
| Speed | Rating | Typical Hardware |
|---|---|---|
| < 4/sec | Slow 🐢 | Office keyboard, 125 Hz polling |
| 4–7/sec | Normal ⌨️ | Gaming keyboard, 500–1000 Hz |
| 7–10/sec | Fast ⚡ | High-end gaming keyboard, linear switch |
| 10–14/sec | Gaming Grade 🎮 | 1000 Hz, low actuation force switch |
| 14+/sec | Rapid Trigger 🚀 | Wooting, analog hall-effect keyboard |
What Actuation Point Setting Is Best for Rapid Trigger?
These benchmarks reflect presses per second (PPS) scores measured in a 5-second burst test. Rapid trigger keyboards score higher because they eliminate the reset dead zone between presses.
| Score | Rating | Who scores this |
|---|---|---|
| 0.1–0.3mm | Ultra-Sensitive | Competitive edge — risk of false triggers if finger rests on key |
| 0.2–0.4mm | Competitive | CS2/Valorant optimal — fast re-actuation, minimal false inputs |
| 0.4–0.8mm | Balanced | Most gaming scenarios — noticeable RT benefit, stable inputs |
| 0.8–1.5mm | Conservative | Similar to fast mechanical — RT benefit reduced but reliable |
| 1.5mm+ | Standard Mode | Approaches traditional keyboard behavior — minimal RT advantage |
Frequently Asked Questions
What is the best actuation point for gaming?▼
The most commonly recommended actuation point for competitive FPS gaming is 1.5–2.0mm. This balances fast registration (you don't need to press very deep) against accidental keypresses (you won't trigger keys from resting your fingers on them). Some aggressive players drop to 1.0mm for lighter touch, but settings below 0.5mm risk misfire from normal typing pressure. The actuation point only affects the initial press depth — rapid trigger sensitivity controls the re-actuation behavior, which is the more impactful setting for counter-strafing.
What rapid trigger sensitivity should I use?▼
Most competitive guides recommend 0.2–0.4mm for rapid trigger sensitivity (the minimum upward travel needed to reset the key for re-actuation). At 0.2mm, the key re-actuates after moving just 0.2mm upward from its lowest point — fast enough for aggressive counter-strafing. Below 0.1mm, most users experience false re-actuations from finger vibration or switch jitter (electrical noise in the Hall Effect sensor). The Wooting team recommends 0.2mm as the minimum safe setting for most users. If you experience accidental double-inputs, increase sensitivity by 0.1mm increments until they stop.
How do I know if my actuation settings are wrong?▼
Signs your actuation point is too shallow (under 0.5mm): unintended keypresses when your fingers rest on keys, missed shots from accidentally triggering movement keys, double-inputs during normal typing. Signs it's too deep (over 2.5mm): noticeably having to 'press harder' than expected, slow registration feel, PPS score that doesn't improve with rapid trigger enabled. Signs rapid trigger sensitivity is too high (over 1.0mm): no noticeable difference compared to a standard keyboard in this test, hold time over 150ms at normal press speed.
Does actuation point affect rapid trigger?▼
Yes and no. The actuation point determines where in the keypress the rapid trigger zone begins: the key only enters rapid trigger mode below the actuation point. If your actuation point is 2.0mm and your rapid trigger sensitivity is 0.2mm, rapid trigger becomes active once you press 2.0mm down, and it will re-actuate after any 0.2mm upward movement from the lowest point of the press. This means a shallower actuation point means more of the key travel is in rapid trigger territory, which is why competitive players lower the actuation point for faster activation.
Can I test my actuation settings with this tool?▼
This tool measures your PPS and hold time — useful benchmarks for evaluating actuation settings indirectly. For direct actuation testing: enable rapid trigger at your current settings, run this test 3 times, and note average PPS and hold time. Then reduce your rapid trigger sensitivity by 0.1mm, retest. If PPS increases and hold time decreases, the lower sensitivity setting is working. If you start seeing false double-inputs, go back up by 0.1mm. This iterative approach is the method recommended in Wooting's and Glorious Gaming's official setup guides.
How do I set actuation point and rapid trigger on my keyboard?▼
The process varies by keyboard brand: Wooting (60HE/80HE) — use Wootility software, select keys, drag actuation and rapid trigger sliders. Glorious GMMK Pro — use Glorious CORE, Actuation tab, enable Rapid Trigger toggle, adjust RT Press and RT Release distances. SteelSeries Apex Pro — use SteelSeries Engine, Per-Key actuation slider (1–4mm). Corsair K70 Max — use iCUE software, Key Performance tab. After adjusting, retest with this tool to confirm the change registers in your actuation speed score.
Last updated: